Have you ever left your bong at a friend’s house? Perhaps you never bought one in the first place, don’t have any other options, or are prepared to try something new. Whatever the matter may be, don’t think too hard since we have a solution to your problem. The Seed Supreme DIY instructions for today will walk you through creating a homemade bong.
Learning how to make a homemade bong is an experience that every true stoner should have at least once in their lives if only to cross it off their bucket list. Nonetheless, we strongly urge you to invest and get a high-functioning model. Don’t become too used to it.
Before we show you how to create a bong out of common household items, you should know that this is not the healthiest way to ingest cannabis. This bong will require plastic and potentially a couple of its constituent components. Smoking with a plastic cigarette is never a smart idea since the heat from the smoke, and the lighter’s heat will allow some of the plastic’s chemicals to enter your bloodstream.
How to Make a Bottle Bong
Materials
- A pen entirely made of metal or at least with a metal tip
- Gum or clay
- A long, empty water bottle
- Ground cannabis of your preference
- A lighter
To properly learn how to create a DIY bong, you must first comprehend the structure and fundamentals of these simple devices.
- The carb or carburetor, a small hole on the side or back of the bong, allows you to alter the airflow with your index finger.
- The tube is the part of the bong where the smoke rises to the lungs.
- The downstream is the thinner pipe that connects the bowl to the water, allowing smoke to move down to the base and back up through the tube.
- The base is where the water sits and cools the smoke.
- The bowl is the container in which your marijuana is stored.
Directions
Step 1
Before you do anything else with your water bottle, make the downstream for your bong. To finish this challenge, you’ll make a pen pipe. The pen you use should ideally be entirely comprised of metal. If that’s not the case, please make sure it has a metal lid that can be unscrewed, the portion that resembles a long bullet.
Step 2
Unscrew the shaft and use a butter knife for popping off the bottom bit. Remove the ink tube and other minor parts (such as the spring) until only the pen’s shaft and metal screw-on top remain. Turn the metal shaft on top upside-down and press the pointed end firmly into the pen’s shaft. Toss the pen’s leftover bits away.
Step 3
Remove the cap from your water bottle and empty it. The next step is to use a lighter to make a small hole in the bottom third of the water bottle, about two or three fingers up the end of it. Remember that you’ll need the empty pen pipe you just constructed to execute this properly. Then, for a few seconds, hold the flame of your lighter against the bottom third of the water bottle.
Step 4
When a small hole emerges in the bottle due to the heat, immediately put the pen through the hole. Because the plastic is now heated, it can mold pretty tightly around the pen shaft. If the opening was too narrow to accommodate the pen shaft, quickly press the lighter on the plastic and try again. This section of the pen should be angled downwards toward the bottom of the water bottle as if it were tilted down.
Step 5
Regardless of how adept you are at lighting a bowl of water bottles, there’s a high chance your shaft isn’t completely centered on the structure. As a result, you’ll need to install a seal around its perimeter. Chewing a piece of gum and wrapping it around the pen shaft just where it connects to the water bottle to establish a seal is a quick and easy solution to this problem. It would be much better if you could locate some clay to secure it.
Step 6
Fill your water bottle until a portion of the pen shaft is immersed. Only fill the water bottle to the point where the water meets the section of the bottle where the pen pierces. Otherwise, the gum or clay will become moist and slip off, possibly a finger’s length away from this wrapping.
Step 7
To make the carb, punch a hole at the other extremity where the pen shaft is using a knife or cutter, large enough to be effective but small enough that your finger can comfortably cover it.
You should have a bong fashioned out of a water bottle by now! Place your ground-up flower in the metal pen tip and light it while inhaling through the top of the water bottle. If you did it correctly, the water should bubble up, and no smoke should escape from the improvised downstem. Furthermore, avoid using foil. Because this is already a risk due to plastic burning, adding this substance to your bong would be even more hazardous to your lungs and health.
Instead, why not go for a healthy option and give a commonplace thing a second life? For example, a pipe stuffed with a juicy apple. This water bottle pipe is a fascinating method to recycle and reuse items that require only patience and basic abilities. However, it should only be done once for your good.
